How to Reprogram a Skoda Key Fob
Many people are wondering how to reprogram their car key fobs, when they aren't sure the reason behind why it isn't working anymore. It's common for key fobs to get damaged or jammed when they're thrown around.
Try changing the battery. If you're not able to get it to work, it might be time to consider a replacement.
1. Switch off the ignition.
It is likely that the battery inside your key fob needs to be replaced if it has stopped working in the last few days. The batteries are affordable and easy to replace and this should be the first step before you attempt to reprogram the key.
Ensure the car is turned off and that all doors are shut. Then put the current key into the ignition and turn it to the "On" position. You shouldn't turn off the engine.
Press the lock button on the keyfob within five seconds. You will hear the car's locks lock and unlock to confirm that you succeeded in entering programming mode. You can now use your key fob both to lock and unlock your car and also program other remotes. This method can be used to reset a damaged or malfunctioning remote. This may be necessary after you've dropped or stepped on or exposed the key fob to water.
2. Switch on the ignition
There are only a few minutes to reprogram the key fobs in the correct way. The first thing to do is turn on the ignition. This will reset the computer and give you a fresh start.
Then, shut all your car doors. You don't need to open any doors during this time as it could cause the program to be interrupted. After you've closed all doors switch the ignition to "On" and insert the key that is the primary one.
After the engine turns on after the engine has started, press the lock key on your fob six times in 10 seconds. If you can hear the doors unlocking in your car then the mode of programming has been successful. Repeat the process for all additional remotes you'll need program. Keep in mind that you must program each remote promptly following the first one, as any delay could cause it to fail.
3. Press the Lock Button
The key fob acts as small remote that can be used to lock and unlock the car. It also comes with the ability to use a panic key which can be utilized in an emergency to seek help. Your key fob might not function for a variety of reasons, such as an unresponsive or damaged battery.
If the key fob isn't working correctly, you can try to reset it by following the steps below. This procedure will work with most cars. However it is imperative that you follow the instructions in the manual for your vehicle.
Start the process by turning on the car using the ignition key, but without starting the motor. Press both the "unlock", "panic", and "lock" buttons on the fob for a few seconds. You will hear a click which indicates that the fob's key is successfully programmed.
4. Unlock the Lock Button
To start and unlock your car, you'll have to pair a brand new key fob to it. You can do it yourself, but you'll need to know how to program an skoda key fob, as well as other things.
To push the lock button in your car, you'll have to utilize a long and slim tool. A wire coat hanger is usually the best option as it's lightweight and long.
Close your car doors after opening them. Press the unlock button on the fob a few times. This will trigger a chime inside your car, letting you know that the fob's key was reprogrammed. After this, you will be able use the unlock and lock button normally. If they don't then you'll need to take your vehicle to an authorized dealer.
5. Press the Panic Button
The "Panic Button" on your key fob is an excellent feature to help you locate your car in crowded parking spaces. It's also a good way to deter would-be thieves. The button can set off an alarm in your car and scare away criminals who may think you're an easy target.
If the panic button does not work after changing the key fob's programming, it could be because the battery was not installed correctly. In this scenario you'll need replace the battery in the key fob.
Open the key fob, and separate the transmitter portion from the main part. Remove the battery that has expired from the transmitter section, then put in a new one that has the correct orientation. Reassemble the keyfob, and test its locking and unlocking capabilities. If The Key Lab doesn't work you will have to repeat the reprogramming procedure or contact a local locksmith.
6. Press the Lock Button
Updated April 17, 2023: If your key fob isn't opening doors, you may have to replace the button cell battery. This tiny coin-shaped silver battery is simple to replace using an screwdriver or fingernail.
Once you have a brand new battery in place, follow the steps to change the programming of the key fob. Always close every door, as the act of leaving a door open could cause the process to be disrupted. After you've done this then turn the ignition on to "On" but do not start the engine.
Press the lock button on the key fob within five seconds after it has been programmed. You should hear a sound as the car locks up, indicating the success of the process. Repeat the process for any additional remotes that you want to program into your car. If the key fob is still not working, the problem could be a wire or antenna problem, software problems or a damaged circuit board. It may be necessary bring it to the dealer to have it reprogrammed.